Phoenix House Rewiring provides whole house rewiring in Phoenix, AZ, including aluminum wiring replacement, knob and tube wiring replacement, and electrical panel upgrades. We replace outdated branch circuits with modern copper wiring suited to your home's electrical needs. Our services also include electrical diagnostics, safety inspections, dedicated circuits, and outlet and switch installation. GFCI and AFCI upgrades, circuit breaker replacement, and whole-home surge protection complete the work when your project calls for them.
Older homes in Encanto, Arcadia, and Sunnyslope can have wiring that struggles with today's appliances and long summer cooling loads. Worn insulation, warm outlets, and recurring breaker trips deserve a careful electrical inspection. Our master and journeyman electricians work under Arizona Registrar of Contractors licensing and assess the wiring before defining the scope. Contact us for a free electrical estimate and rewiring consultation based on a walkthrough of your property.
We coordinate permits and inspections through the appropriate City of Phoenix or Maricopa County building department. Your project includes a written scope and a final walkthrough with inspection documentation.
Rewiring with Accountability
A complete rewire reaches from the panel to the outlets, switches, and fixtures you use every day. These services address aging wire materials, circuit capacity, fault diagnosis, and the protective devices needed for a modern home.
Aluminum branch wiring was common in Phoenix subdivisions built between roughly 1965 and 1973. We replace original runs with copper conductors sized for the circuit load and discuss phased work or approved connector methods when replacement cannot be completed in one phase.
Explore Service
In pre-1950s homes around Willo and Coronado, knob and tube replacement starts with tracing the existing runs through walls and attics. We de-energize the old wiring, install grounded copper circuits, and plan patching around the home's original finishes.
Explore Service
We replace fuse boxes and undersized 60 to 100-amp services found in Maryvale and South Phoenix homes. Panel selection accounts for HVAC, EV charging, pool equipment, and added circuits, with 200 amp service recommended for most single-family homes after reviewing demand.
Explore Service
Flickering lights, warm outlets, repeated breaker trips, or a burning smell near the panel call for diagnosis. We trace the affected circuit and isolate the fault so the repair addresses the cause.
Our inspection checks panel condition, grounding, attic wiring, and fire-damaged or rodent-chewed sections before replacement work begins. The findings establish a written scope for the circuits, equipment, and access your project needs.
Shared 15-amp circuits can be a poor fit for kitchens, workshops, and home offices with substantial appliance loads. We install dedicated circuits for ranges, dryers, HVAC condensers, pool equipment, and EV chargers, sized to each appliance's draw.
We install GFCI protection for areas such as kitchens, bathrooms, garages, and outdoor outlets, and AFCI protection for applicable living-area circuits. These upgrades are planned alongside the wiring and panel work required for your home.
Inspections can reveal worn or recalled breakers that need replacement. We assess breaker condition and replace devices that no longer trip correctly as part of resolving the circuit or panel problem.
We install outlets and replace switches throughout the home, including dimmers and connected controls. During rewiring, planned device locations and smart home wiring are included in the project scope.
Panel-mounted surge protection gives the home's circuits a first line of defense against voltage surges. We include it in electrical upgrade planning for HVAC equipment, appliances, and electronics exposed to Arizona storm conditions.
The right scope depends on what is behind the walls and what you want the home to support. We plan complete circuit replacement, historic-home access, service capacity, and project costs together so each stage has a clear purpose.
A full rewire replaces branch circuits, boxes, and terminations throughout the home. We plan circuit counts around today's appliances and electronics, including homes whose original 1960s-era 60-amp service no longer fits their use.
Electrical work in older Encanto, Willo, and Coronado homes requires careful routing through existing construction. We plan access, wiring replacement, and finish repairs with attention to the home's original character.
A 100A panel offers limited capacity in many pre-1980 homes, while 150A can suit moderate loads and some mid-size remodels. A 200A panel supports the broader needs described for modern homes and most rewires, with the final choice based on the home's demand.
Whole house rewiring in the Phoenix market generally ranges from $4,500 to $20,000, with most projects landing between $8,000 and $12,000 depending on size and access. Homes under 1,500 square feet often fall near the lower end; larger or multi-story properties with difficult access cost more. We walk the property before providing a written estimate.
Our process brings inspection findings, permit coordination, and a written scope into the same plan. From older subdivisions to remodeled homes, we explain the work your electrical system needs and document its completion.
Our team works under active Arizona Registrar of Contractors licensing and carries commercial general liability coverage for rewiring and panel projects. Master and journeyman electricians handle legacy equipment and modern controls, from a 1962 fuse panel to a 2024 smart home system.
Phoenix housing spans more than seven decades, with original wiring still found in neighborhoods such as Sunnyslope, Maryvale, and parts of Ahwatukee. We plan around older subdivisions, mid-century ranch homes, and remodeled properties with different access and circuit needs.
We arrange permits for rewires and panel upgrades through the appropriate city or county building department. A final walkthrough and inspection sign-off provide documentation of the completed work.
Original wiring and limited panel capacity can become harder to live with as electrical demand grows. An inspection helps separate a single circuit fault from a broader wiring or service issue and establishes the next step.
Request a Free EstimatePhoenix attic temperatures can pass 150 degrees in summer, putting old insulation through repeated heat cycles. Homes built through the 1950s, 1960s, and 1970s may still have original components, so worn insulation and physical damage are key inspection concerns.
Aluminum conductors expand under load and can oxidize at connections. As terminations loosen over time, outlets and switches may overheat; the repair scope needs to address the affected wiring and connections.
Older knob and tube wiring lacks the grounding found in modern branch circuits, and its rubber insulation may be deteriorated. Replacing these runs with grounded copper wiring addresses the aging system and supports updated devices.
Long summer HVAC run times add sustained demand to the home's electrical system. An undersized panel may also need to accommodate an EV charger, pool equipment, or new appliance circuits, making capacity review essential.
A repeatedly tripping breaker or warm outlet is a symptom to investigate. Circuit-by-circuit diagnostics help establish whether the work involves damaged wiring, a device connection, or a breaker that needs replacement.
Phoenix's monsoon season brings lightning activity from June through September, exposing electronics and major equipment to surge risk. Panel-level protection is one part of an upgrade plan that also considers wiring condition and protective devices.
For a typical 1,500 to 2,500 square foot Phoenix home, rewiring generally takes 3 to 7 working days. Attic access, slab construction, wall opening, and inspection scheduling affect the work plan, which moves from inspection and scope through rough-in and finish work.
We assess the panel, grounding, attic wire runs, and damaged sections before any wire is removed. The inspection identifies what needs replacement and what access the project will require.
We review circuit needs, panel work, wall materials, and wire-routing access. Planned EV charging, dedicated circuits, and smart home devices belong in this discussion so the written estimate reflects the intended project.
We coordinate the permit process and inspection schedule, then walk you through a preparation checklist. Clear access to the panel and attic, move furniture from affected walls, and plan for temporary power interruptions.
The work area is de-energized before the old wiring is removed or taken out of service. New copper circuits are routed through available wall and attic spaces as part of the rough-in stage.
Rough-in inspection is followed by finish work with outlets, switches, and fixtures reconnected. Wall openings and patching are addressed according to the agreed scope, with historic finishes considered in the work plan.
We finish with a walkthrough and final inspection sign-off. The completed documentation records the work, while the walkthrough gives you an opportunity to review the updated electrical system.
We serve the Salt River Valley and greater Phoenix metro area, a region spanning over 517 square miles and home to more than 1.6 million residents. Our work includes central historic neighborhoods, North Phoenix homes, and communities in South and East Phoenix, with the scope adapted to each property's wiring and construction.
Tell us about the home's wiring concerns, planned appliances, and any inspection findings. Phoenix House Rewiring will walk the property, discuss the required work, and provide a written electrical estimate based on the actual scope.
Explore common questions about rewiring costs, panel upgrades, project timing, and preparing your home. Your inspection and written scope determine how those details apply to the property.
Call Our ExpertsOften, yes, if the existing copper branch wiring is in good condition. Many homes with copper wiring from the 1980s and later may only need panel replacement, while older aluminum or knob and tube circuits need a closer review. We inspect the wiring before deciding whether panel work should be paired with a partial or full rewire.
Modern copper wiring installed to code can last 40 years or more without replacement. Older wire materials, damaged insulation, and circuit condition can make replacement necessary sooner, so age alone does not determine the scope. If a home built before 1980 has never been rewired, an electrical safety inspection is a useful starting point.
Before starting homeowner electrical work, confirm the permit and inspection requirements with the City of Phoenix or the relevant county building department. Whole-house rewiring involves power shutdowns, new circuits, code requirements, and inspections at multiple stages. Our electricians manage the electrical work, permitting, and inspection scheduling for these projects.
A typical single-family rewire takes 3 to 7 working days, with larger or multi-story homes sometimes taking longer. Attic and crawlspace access, wall opening and patching, and city inspection scheduling all affect timing. Plaster walls or block construction can require more careful routing than standard drywall.
A full rewire involves de-energizing the home, taking old wiring out of service, routing new circuits, and coordinating inspections. Working through existing walls and attic cavities makes access a major part of the job. The project also requires planning around the occupants, temporary power interruptions, and reconnection of outlets, switches, and fixtures.
Clear access to the attic, crawlspace, and panel, and move furniture away from walls where devices will be installed. Plan for temporary power interruptions and keep pets and sensitive equipment away from active work areas. Tell us about planned EV charging, smart home wiring, or dedicated circuits during the consultation so they are included in the scope. We provide a preparation checklist for your project.
For that home size, Phoenix rewiring typically falls between $6,000 and $15,000, depending on wall construction, attic access, and whether panel work is included. At roughly $2.65 per square foot for labor and materials, a 2,200 square foot home comes to about $5,800 for wiring alone. Panel upgrades, permits, and drywall patching add to the total, and we provide a property-specific figure after a walkthrough.
We check the panel, grounding, attic wire runs, and damaged wiring, including fire-damaged or rodent-chewed sections. We also review access conditions and the circuits your household needs. These findings form the written scope before replacement work begins.
We can scope aluminum replacement room by room when the project needs to be phased. Full replacement uses copper conductors sized for the circuit load, while approved connector methods may be considered where replacement cannot be completed in one phase. The inspection determines which approach fits the existing wiring.
Panel upgrades typically take one to two days, including the utility disconnect and City of Phoenix inspection. Panel size, meter configuration, and any required service line relocation affect the work and cost. The project plan also accounts for the added circuits and equipment the new panel must support.
Our dedicated circuit work includes ranges, dryers, HVAC condensers, pool equipment, and EV chargers. Each circuit is sized to the appliance's actual amperage draw and protected by its own breaker. We review planned equipment during the consultation so those circuits are included in the estimate.
Yes, GFCI and AFCI upgrades can be planned with a full rewire, along with outlets, switches, dimmers, and connected controls. We review the wiring and protection needed for each part of the home. Mention smart home plans early so device locations and circuit needs are included in the scope.
We install whole-home surge protection at the electrical panel to give the home's circuits a first line of defense. It is intended to support protection for equipment such as HVAC systems, electronics, and appliances. We discuss it alongside other wiring and protective-device upgrades during project planning.
Wall construction, wire-routing access, panel replacement, and the amount of drywall repair all affect the scope. We inspect the home before writing the estimate so these items can be discussed together. Historic masonry and difficult attic access can increase labor even when two homes have similar square footage.